Home → Brake Pads → Brakes - GPFAX757HH Grand Prix - EBC (Front)

Brakes - GPFAX757HH Grand Prix - EBC (Front)

Brand: EBC Brakes

Category: Brake Pads | Part No GPFAX757HH

Brakes - GPFAX757HH Grand Prix - EBC (Front)

Photos are for reference only

Ask a question

M.R.P.

Rs. 7,500.00   /-

inclusive of all taxes


DELIVERY QUESTIONS ? Shipping & Delivery FAQ's

COUNTRY OF ORIGIN: UNITED KINGDOM

BEST BEFORE: TEN YEARS FROM DATE OF IMPORT / PACKAGING

WARRANTY INFO: MANUFACTURER WARRANTY

COMMON GENERIC NAME : MOTORCYCLE SPARES AND PARTS

NET QUANTITY : 2N (1 SET)

Would you like to Preorder this? Know More!

FITTING INFO: RACE USE PADS ( NOT FOR STREET / HIGHWAY)

FREE UPGRADE TO FASTER AIR SHIP ON THIS

Part No GPFAX757HH

Have something to say about this product? Compatibility or fitment related! Bring it to our order processing teams attention, by writing below

This product is not in Stock!

Timelines of delivery:- At-least five to eight weeks from your pre-order date !

← Previous Product Next Product →
For "Fitment and Compatibility"; please check the section above

GPFAX is the new compound that replaces GPFA 

  • ONLY FOR RACE USE
  • The highest performance friction level known
  • NOT R90 street legal or TÜV tested
  • Guaranteed for lifetime performance

    GPFAX Sintered Road Race Brake Pads have by far the highest known friction with a measurement between 0.6 and 0.7 and deliver the most amazing brake effect. Because of this factor, they are unsuitable for street use or for road tires.

    Zero brake fade is guaranteed and the heat stability of these brake pads is perfect leaving the racer with high confidence and a product that can be used over numerous races.

    GPFAX Sintered Road Race brake pads are a closed circuit use pad only and street/highway riding with this material is highly inadvisable and dangerous. Such high friction levels as delivered by these pads are for ideal track conditions with race tires or slicks on prepared asphalt surfaces and NOT for use with highway tires or on the highway. This material is not ECE R 90 approved nor TUV tested with a German ABE and use on the highway is, therefore, illegal in many countries.

    The material quickly builds from an initial friction level of 0.6 ( which in itself is a massive brake friction level rarely achieved by any competitor material) up to a huge 0.7 with a minimum in-stop friction level of 0.65. This tiny fall off from 07 – 0.65 during braking would be almost undetectable by the rider allowing superb brake feedback and control at the lever and allowing feathering of the brake predictably and steadily throughout deceleration.

    The new material also wears better and causes lower rotor/disc damage than previous materials and should be good for 4-5 race events of a typical 20-25 lap duration minimum. Pads should be discarded when less than 2.5 mm of friction material remains to avoid fluid vapor lock due to excess piston fluid volume.

    This material contains no toxic lead nickel or zinc which is a trick used by our competitors to ramp up friction levels the cheap way.

    Preparing your Race discs/rotors before using this Compound 
    Many pads contain carbon particles some in high percentages and this leaves a grey glaze on rotors. This MUST be removed by fine abrasive paper or what is known as a Scratch Pad in the USA. Take care not to promote deep scratches on the rotor which will cause prolonged bedtimes.

     

    Correct usage!

    Bedding in your new brake pads

    After installing the pads ride the bike for 2 laps very gently applying the brakes well in advance of where you wish to stop at speeds not exceeding 80 MPH.

    Proceed a further 2-3 laps gradually increasing the brake load until you feel the pads become stable and predictable.

    Bedding into worn or distorted discs/rotors will be dramatically longer.

    Inspect pads every Race for wear on EACH pad and replace when any single pad is down to 2.5 mm or lever becomes spongy. Different brake systems respond differently and have differing amounts of fluid in their piston chambers and the time for an ideal replacement of the pads due to loss of brake feel can only be assessed by the individual rider and bike

    Brake fluid considerations

    Old brake fluid affects the sponge and brake feel. Most brake fluids are Glycol based and over time their hygroscopic nature means they will absorb moisture even through the brake lines. As amazing as this sounds it does happen and fluids can contain as much as 12% water by volume in worst cases.

    It is highly advised to replace brake fluid every 6-8 race events as a minimum with a high wet boiling point fluid such as Maxima Race fluid. Use only fluids from a sealed container, never from a bulk can or drum as in this storage condition the fluid will act like an old material even before you use it having absorbed water since originally opened.

    Brake discs/Rotors for race use needed

    MANUFACTURER :FREEMAN AUTOMOTIVE LTD | COUNTRY OF IMPORT : UNITED KINGDOM
    Imported & Marketed by : Plusgrow Merchantry Pvt Ltd (U51909MH2018PTC318387) T 31A, MIDC INDUSTRIAL AREA, HINGNA RD, NAGPUR 440016 MH

    ALL PICTURES SHOWN ARE FOR ILLUSTRATION PURPOSE ONLY. ACTUAL PRODUCT MAY VARY.

    Disclaimer: While Motousher works to ensure that the product information, on the website, is accurate and correct, on occasions, the concerned manufacturers may alter or modify their products' ingredients or configurations, as the case may be. Actual product packaging and materials may contain more and/or different information than that is shown on Motousher's website. Motousher recommends that you do not solely rely on the product information available on the website and that you always read warnings, descriptions, labels and directions, printed on the product, before using or consuming a product. For any additional information about a product, please contact the concerned manufacturer or refer to their website.